Jump to content

Search the Community

Showing results for tags 'dallas'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Thank you for chosing everything EPOS
    • About us
    • General Chit Chat
  • ICR Touch - Support & Guides
    • Quick Guides
    • ICR Support
  • myEPOS Touch - Support & Guides
    • Quick Guides
  • encomPOS Retail - Support & Guides
    • Quick Guides
    • Retail Support
  • Drivers / Integration & Cables / Wiring
    • Cable Diagrams
    • Quick Guides
    • Drivers
    • Windows Issues
    • Hardware Configuration
  • Card Processing
    • Payment Sense
  • CCTV
    • Geovision
    • Hikvision
    • Other CCTV Guides
  • myEPOS Online
    • myEPOS Technical

Categories

  • General Downloads
  • ICR Downloads
    • ICR Manuals & Guides
    • Software
    • Utilities
  • ECR Downloads
    • Software Downloads
  • encomPOS Retail Downloads
    • Symbol Group Documents
    • Scripts & Enhancements
    • Retail Manuals
    • Handheld Devices
  • Miscellaneous
  • Card Processing & Other Integration
  • Windows CE
  • Hardware
  • CCTV
    • Hikvision

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Forename


Surname


Company


Address


Telephone


Location


Interests

Found 2 results

  1. To Configure a Tysso Dallas Reader you will need the tool attached to configure. It installs into Program Files, SysKing,CID Test AP Install and launch the tool, Press the Connect Button then select the USB (HID) Tab Leave the Vendor ID as 0E6A but set the Device ID to 30F and press OK As long as it can find the USB Reader the Configure Word Button will appear On the right hand side under 'iButton' you have the Desired settings, so for ICR Touch for example On iButton Head = %DALL On iButton Tail = ?\CR (The \CR is selected from the Invisible Code Dropdown) Off iButton Head = %DALL? Off iButton Tail = \CR Once done - Press the Set Configure word - All Done ! CIDTestApV0601.zip
  2. Jumper setting for iButton Reader Jumper setting for iButton Reader: Jumper Short Open Default setting Switch ON Off RS232 iButton Keyboard iButton SW1: LCtrl-A, LCtrl-Z Send LCtrl-A key in prefix and LCtrl-Z key in suffix when iButton attach. No Send Off SW2: Last 4 Bytes SendLast4Byte SendAllByte (8Bytes) Off SW3: No Pre/Post Amble Nothing Send Pre/Post Amble Off SW4: Enter SendNextEnter NoSend Off SW5: iButton interface RS232 interface Keyboard interface On Off SW6: (Reserved) Off SW7: RS232 TX# For iButton For MSR On Off SW8: RS232 RX# For iButton For MSR On Off Keyboard interface iButton Reader output format: Ø Output when iButton attach: [LCtrl-A key] [ASCII (||||||)] <8Bytes iButton ID or last 4Bytes iButton ID> [ASCII (`)] [Enter key][LCtrl-Z key] [Long beep sound 580us] Ø Output when iButton remove: [ASCII (||||||`)] [Enter key] RS-232 interface iButton Reader output format: Ø Output when iButton attach: [LCtrl-A key] [ASCII (||||||)] <8Bytes iButton ID or last 4Bytes iButton ID> [ASCII (`)] [Enter key][LCtrl-Z key] [Long beep sound 580us] Ø Output when iButton remove: [ASCII (||||||`)] [Enter key] iButton ID definition: Byte[7] for CRC code Byte[6~1] for serial number Byte[0] for iButton Family Code <SW1: Ctrl-A,> <SW3:PreAmble><check SW2 to output 4Bytes or 8Bytes iButton ID> <SW4:Enter><SW1:Ctrl-Z> <SW3:PostAmble><SW4:Enter> For Use with ICR Touch / encomPOS - most sucessful configuration is :- SW1 - OFF - Don't send Ctrl A/Z SW2 - OFF - Send All Bytes SW3 - OFF - Send Pre/Post Amble SW4 - ON - Send Enter Key at end of read SW5 - OFF - Keyboard Interface for MSR SW6 - OFF - Reserved SW7 - OFF - KB Wedge for MSR TX SW8 - OFF - KB Wedge for MSR RX
×
×
  • Create New...